low cost - high performance PSA1200A-LF basestations satellite communications 5 33 03 1200 5000 -103 -15 2 2 1000 50 0 to 60 oscillation frequency range phase noise @ 10 khz offset (1 hz bw, typ.) harmonic suppression (2nd, typ.) tuning voltage tuning sensitivity (avg.) power output load impedance input capacitance (max.) pushing pulling ( db return loss, any phase) operating temperature range package style pll-24 mhz dbc/hz dbc vdc mhz/v dbm pf mhz/v mhz c vdc ma supply voltage (vcc, nom.) supply current (icc, typ.) all specifications are typical unless otherwise not ed and subject to change without notice. phase noise (1 hz bw, typical) ? z-communications, inc. all rights reserved page 1 voltage controlled oscillator features applications performance specifications value units power supply requirements application notes 1200 1200 - mhz ? frequency range: ? tuning voltage: vdc - style package pll-24 ?? ? ? a1 rev ? an-100/1 : mounting and grounding of vcos ? an-102 : proper output loading of vcos ? an-107 : how to solder z-comm vcos notes: reference oscillator signal: 5 mhz< <100 mhz frequency synthesizer: analog devices - adf4106 9939 via pasar ? san diego, ca 92126 tel (858) 621-2700 fax (858) 621-2722 - 1200 offset (hz) (f) (dbc/hz) 14
1090 1110 1130 1150 1170 1190 1210 1230 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 -3 -2 -1 0 1 2 3 4 5 1103 1123 1140 1155 1168 1181 1194 1206 1218 1231 voltage controlled oscillator ? z-communications, inc. page 2 printed in the u.s.a. PSA1200A-LF tuning curve, typ. power curve, typ. page 2 physical dimensions c c c 60 0 25 0.140 .032 17 19 15 13 1 2 3 4 8 10 12 24 22 20 p1 rf output p2-4 ground p5 reference oscillator input p6 ground p7 clock p8 data p9 ground p10 load enable p11 ground p12 lock detect p13 vcc p14 ground p15 ground p16 ground p17 no connection p18-24 ground .015 .030 .055 detail b (typ) see detail a see detail b 1. the inside radius of all 24 half holes at the perimeter of the board are plated to provide a surface for the attachment of the pll module to the pcb. 16 pads are for grounding, 8 pads are for signal interface. 2. the surface of the shield is tin-plated and may be soldered to. the shield's base metal is cold rol led steel. 3.the ground plane on the bottom side is ground and attaches to a ground track on the top side of the board as well as to the shield. 4. unless otherwise noted all dimensions are in inches. 5. unless otherwise noted all tolerances are as follows: .xxx = .010 tabs range: see note 5 (4 places) detail a pin 1 5 6 7 9 11 14 16 18 21 23 top bottom (8 places) 0.025 0.178 0.263 0.348 0.433 0.518 0.603 0.688 0.000 0.866 0.026 0.141 0.226 0.311 0.396 0.481 0.606 0.000 0.631 0.841 pll-24 415-0089 rev. a (drawing not to scale) tuning voltage (vdc) frequency (mhz) power output (dbm) frequency (mhz) c c c 60 0 25
|
